Where is the thermal fuse on a Maytag Bravos MCT dryer?

Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won’t start or will run but not heat. The thermal fuse cannot be reset.

Full Reset It is not uncommon to need to reset a dryer after an error code has been resolved or if the dryer shut down to prevent a thermal overload. Disconnect the power to the Maytag dryer and wait 30 minutes. After 30 minutes, restore power and make a new selection.

Similarly, how do I reset my thermal fuse? How to Reset a Thermal Fuse

  1. Unplug the clothes dryer’s power cord from the wall outlet.
  2. Swing the front panel out towards you so that you can look into the compartment.
  3. Aim a flashlight at the flat-can-like component to locate the blown thermal fuse.

Beside above, how do I know if my thermal fuse is blown?

Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. If this is the case, don’t fret: thermal fuse replacement is a simple task.

Why is my Maytag Bravos dryer not heating up?

Always check the dryer venting when replacing a blown thermal fuse. Gas dryers have two or more gas valve solenoid coils. The gas valve solenoids open the gas valve ports to allow gas to flow into the burner assembly. If the igniter is not working, the gas will not ignite, preventing the dryer from heating.

How do you reset a Maytag?

Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

Where is the thermal fuse located?

Thermal fuses are installed on the dryer’s exhaust duct. Typically, you must remove the back panel of a dryer to access the fuse. Ensure to shut off electrical power to the dryer before attempting to locate and troubleshoot the fuse.

Do Maytag dryers have fuses?

Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won’t start or will run but not heat. The thermal fuse cannot be reset.

How do you test a thermal fuse?

How to Check a Dryer Thermal Fuse Unplug the dryer and remove the front access panel. Locate the blower cover–it’s the large object facing you at the bottom of the dryer. Remove the wires from the thermal fuse terminals to test it. Set your multimeter to the R x 1 scale and touch the leads to the thermal fuse terminals to test for continuity.

Are all dryer thermal fuses the same?

All dryers sold in the United States are legally required to have a thermal fuse. This is different from the electrical fuses that are found in many appliances, and a dryer might have both. A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current.

How do you bypass the thermal fuse on a Maytag dryer?

Locate and Bypass the Fuse The thermal fuse will look like a thin strip of white plastic with a wire coming out of each end. In order to bypass the thermal fuse, use electrical tape to tape the two ends together. The thermal fuse will then be bypassed. Turn the dryer on to a heat cycle for no more than 90 seconds.

How much does it cost to replace a thermal fuse in a dryer?

Cost of Dryer Heating Elements Heating element replacements cost between $30 and $200 dollars on average, depending on the part needed.

What causes a thermal fuse to fail?

The leading cause of thermal fuse burnout is obstructed airflow. Check the exhaust path for excessive lint or debris all the way to the exit point of the exhaust pipe. Check the blower wheel to make sure it isn’t broken or clogged up. This can be done by using “cool down” or “air fluff” mode.

Will a dryer start with a blown thermal fuse?

If the drum light doesn’t turn off, a failed door switch is the likely reason the dryer won’t start. A blown thermal fuse often prevents an electric dryer from starting. You’ll find the thermal fuse on the blower housing. Unplug the dryer and check the thermal fuse for continuity.

Why does my dryer have no heat?

With an electric clothes dryer, no heat often means that the circuit breaker or fuse that controls the power has blown; reset or replace it. Be aware that a dryer may have two breakers or fuses. The motor will run when one works, but the heating element requires both.

Where is the reset button on a dryer?

Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.